› Analysis of the Effect of Grooves in Single and Twin Axial Groove Journal Bearings under Varying Load Direction - Francisco Brito, Universidade do Minho, Mechanical Engineering and Resource Sustainability Center
09:50-10:30 (40min)
› Compliance tests of the polymer layers used as hydrodynamic bearing coatings - Michał Wasilczuk, Faculty of Mechanical Engineering, Gdańsk University of Technology
09:50-10:30 (40min)
› Deflectional and vibrational behaviour of a highly loaded, high aspect ratio hollow shaft equipped with plain journal bearing at the maximal deformation point - Bálint Pap, Hispano-Suiza, Groupe SAFRAN, Institut P' CNRS - Université de Poitiers - ENSMA UPR 3346 SP2MI
09:50-10:30 (40min)
› Elevated vibration of an 110 MW generator Bearing - Nicolas Peton, GE
09:50-10:30 (40min)
› Experimental Investigation of Smart Journal Bearing with Giant Magnetostrictive Actuator - Wen Wang, Shanghai University
09:50-10:30 (40min)
› High Speed Hydrodynamic Journal Bearings – State of the Art of Calculations - Andreas Fuchs, Delta JS AG
09:50-10:30 (40min)
› Inertial method of viscosity measurement of the complex rheology media - Alexey Kornaev, Department of Mechatronics and International Engineering, State University – ESPC, Oryol, Russia - Leonid Savin, Department of Mechatronics and International Engineering, State University – ESPC, Oryol, Russia - Alex Babin, Department of Mechatronics and International Engineering, State University – ESPC, Oryol, Russia
09:50-10:30 (40min)
› Integral centering spring squeeze film damper on the vibration stability of journal bearing-rotor system: modeling and experimental validation - Wang Xiaojing, Department of Mechanical Engineering and Automation, Shanghai University, Shanghai
09:50-10:30 (40min)
› Journal and thrust bearings with textured surfaces: A review of modelling techniques - Daniel Gropper, National Centre for Advanced Tribology at Southampton
09:50-10:30 (40min)
› Partitioned Fluid-Structure Iteration Techniques Applied to the Conformal EHL Solution of Dynamically Loaded Connecting-rod Bearings - Francisco Profito, Department of Mechanical Engineering - Imperial College London, Universidade de São Paulo - Daniele Dini, Department of Mechanical Engineering - Imperial College London
09:50-10:30 (40min)
› Synergistic effects of lubricants on tribological behavior of thermoplasticcomposite materials for dry bearing applications - Yan-Ming Chen, CEntre Technique des Industries Mécaniques
09:50-10:30 (40min)
› The effect of dimples geometry in sliding surface on the tribological properties in starved lubrication conditions - Lidia Galda, Rzeszow University of Technology
09:50-10:30 (40min)
› Thrust hydrostatodynamic bearing with a controllable supply of the lubricant - Alexander Babin, Department of Mechatronics and International Engineering (State University - ESPC)
09:50-10:30 (40min)
1 : Paliers sous conditions de fonctionnement sévères
Michal Wasilczuk
› A study the tribological characteristics on mixed and boundary lubrication condition for tilting pad bearing materials. - Hiromitsu Katsuki, Daido Metal Co.,Ltd.
10:30-11:00 (30min)
› Hydrodynamic plain bearings for mixed friction conditions – a material and design solution of Schaeffler - Michael Plogmann, Schaeffler Technologies AG & Co KG
11:00-11:30 (30min)
› Application of an enhanced 900mm Tilting Pad Bearing in Large Steam Turbines - Ümit Mermertas, Ümit Mermertas
11:30-12:00 (30min)
› Thermal Effects on a Hydrodynamic Bearing's Clearance with Consequence to Seizure - minel jack braun, University of Akron, Dept off Mechanical Engineering
14:00-14:30 (30min)
› On the influence of the presence of geometrical discontinuities on journal bearing performance under thermohydrodynamic regime - célia giraudeau, Institut P' CNRS - Université de Poitiers - ENSMA UPR 3346 SP2MI, EDF R&D
14:30-15:00 (30min)
› Field measurement techniques and instrumentation for torsional vibrations determination - nicolas peton, GE
15:00-15:30 (30min)
› Experimental comparison of the hydrodynamic thrust bearings with different coatings - Michał Wodtke, Faculty of Mechanical Engineering, Gdańsk University of Technology
16:15-16:45 (30min)
› Performance of a PEEK Lined, Tilt Pad Thrust Bearing at High Speeds with Oil Lubrication - JIE Zhou, Waukesha Bearings Corp.
16:45-17:15 (30min)
› Comparison of PEEK and PTFE materials for polymer coated thrust bearings of vertically aligned hydro power units - Andreas Schubert, ALSTOM Hydro
17:15-17:45 (30min)
› Innovative geometrical enhancement and use of composite coating structures to improve lifetime and performance of thrust bearings. - Chris Walker, Chartered Institute of Marketing, Diamond Hard Surfaces Ltd, Institute of Mechanical Engineers
17:45-18:15 (30min)
› CFD analysis for the sprayer design of a direct lube tilting pad journal bearing - Libraschi Mirko, GE oil and gas
08:00-08:30 (30min)
› Multiphysical modeling comprehensiveness to model a high speed Laval rotor on journal bearings - Rob Eling, Delft University of Technology, Faculty 3mE, Department PME, Mitsubishi Turbocharger and Engine Europe
08:30-09:00 (30min)
› Numerical optimization and response surface mapping by experimental design of tilting pad bearings - Michael Branagan, Rotating Machinery and Control (ROMAC) Laboratory, Department of Mechanical and Aerospace Engineering, University of Virginia
09:00-09:30 (30min)
› 3-D Thermohydrodynamic Analysis of Textured, Grooved, Pocketed and Hydrophobic Pivoted-Pad Thrust Bearings - Christos Papadopoulos, National Technical University of Athens
09:30-10:00 (30min)
› Application of hydrodynamic radial bearings on large fossil steam turbine generators: selection of bearing types and use of dimensionless bearing dynamic coefficients in rotor dynamics analyses - Josef Huster, ALSTOM Power AG, Dept. of Transverse Technologies, ALSTOM Power AG, 5400 Baden, Brown Boveri Str. 7, Switzerland
10:30-11:00 (30min)
› Realistic Non-Destructive Evaluation of Journal and Thrust Bearings, especially for Post-Service Evaluation and after Refurbishment - Lyle Branagan, Pioneer Motor Bearing Company
11:00-11:30 (30min)
› New ecologically friendly tin base alloy from ZOLLERN BHW for highly loaded bearings - Edgar Gust, Edgar Gust
11:30-12:00 (30min)
› Performance comparison of Tokat® and babbitt for a Francis turbine's upper thrust bearing - Luciano Andriani, Kugler Bimetal SA
12:00-12:30 (30min)
